Care home controls - water safety, scalding and heatwaves
A care home is not a small hospital and not a large house. Its residents are often frail, many cannot easily tell anyone they are too hot or too cold, and the building runs day and night all year. The controls are usually modest - boilers, zone controls, hot water storage, thermostatic mixing valves and perhaps a light BMS - but what they protect is not modest at all.
In a care home the value of controls work lies less in energy saving and more in safety, comfort and evidence. This article is for integrators who look after care homes or care groups. It covers the water temperatures that matter, how logging turns into evidence for inspectors, how to prepare for heatwaves, and the boiler and setback faults that come up most.
Two duties that pull in opposite directions
Hot water in a care home has to be hot enough to control legionella and safe enough not to scald. The Health and Safety Executive sets out both.
- Legionella control. Hot water should be stored at 60°C or above, with cylinder temperatures checked monthly (HSE - legionella in health services). Health and social care settings apply the HSG274 Part 2 guidance proportionately, through a local risk assessment (HSE - hot and cold water systems).
- Scald protection. Where vulnerable people can reach baths or showers and the scald risk is significant, a Type 3 thermostatic mixing valve (TMV3) must be fitted so water does not exceed 44°C, and NHS settings require showers to deliver no more than 41°C (HSE - scalding and burning).
The store runs hot and the outlet is blended down. HSG274 Part 2 adds that hot water should reach 55°C at outlets within a minute in healthcare premises (50°C elsewhere) and that cold water should stay below 20°C (HSE HSG274 Part 2) - the written scheme says which applies.
| Hot water stored - at or above | 60°C |
|---|---|
| Hot water at outlets within one minute - at or above (healthcare premises) | 55°C |
| Baths behind a Type 3 TMV - no more than | 44°C |
| Showers in NHS settings - no more than | 41°C |
| Cold water - below (HSG274) | 20°C |
Legionella control and scald protection pull in opposite directions - the store runs hot and the outlet is blended down. The local risk assessment sets the regime.
Logging as evidence
The Care Quality Commission links legionella control to Regulation 12 (safe care and treatment) and Regulation 15 (premises and equipment). A provider stays responsible for legionella control even if it does not own or manage the building, and new providers are asked for a legionella risk assessment (CQC).
Most homes still record water temperatures by hand, once a month, on paper. Continuous logging is where controls add the most value:
- Calorifier and return temperatures logged every few minutes, with an alarm if the store falls below 60°C or the return falls below its agreed limit.
- Sentinel outlets - the nearest and furthest outlets on each circuit - logged where sensors can be fitted, or checked and entered where they cannot.
- TMV outlets monitored where the risk assessment calls for it, with an alarm on any reading above the limit.
- A monthly report that the manager can hand to an inspector, showing the readings, any excursions and what was done about them.
A trend with every reading kept is far stronger evidence than a sheet with one tick a month, and it shows problems the monthly check would miss - a store that dips every morning when demand peaks, for example.
Heatwaves - the growing risk
UKHSA's Adverse Weather and Health Plan (April 2023) replaced the Heatwave Plan for England, and NHS England asked care home managers among others to read it, including the risk from indoor overheating (NHS England letter). UKHSA and the Met Office issue Heat-Health Alerts with yellow, amber and red action cards, and organisations can register to receive them (GOV.UK action cards). UKHSA-commissioned research found significant excess deaths in care homes during heatwaves (GOV.UK research).
The controls part is simple to describe and valuable to deliver:
- Room temperature sensing in residents' rooms and lounges, especially those facing south or west and on upper floors.
- A heat dashboard that shows which rooms are warmest, tied to the alert level, so staff know where to act first.
- Alarms at agreed thresholds set with the home's management. The indoor threshold often quoted for care homes could not be confirmed against the UKHSA guidance, so agree the figure with the client rather than assuming one.
- Heating locked off in hot weather. It sounds obvious, but heating left enabled by a summer timeclock or a frost setting set too high is a common find.
Setback limits for frail residents
Night setback and holiday modes save energy in offices and schools. In a care home they need limits. Residents may be in bed all day, and many feel the cold more than staff do. Any setback should be agreed with the home's management, kept to modest reductions in communal areas, and never applied to residents' rooms without a clear decision. The saving is small compared with the risk.
Boilers that short-cycle
Care homes often have boilers sized for the coldest day and for a hot water peak that rarely comes. In mild weather, an oversized boiler with a narrow control band fires, overshoots and stops within minutes, then fires again. Each start purges heat up the flue and wears the burner. Wider differentials, minimum on and off times, working modulation and proper sequencing of multiple boilers all help - and they should be checked against the hot water demand, because the calorifier still has to hold its temperature.
How care groups buy
Care groups often buy hard facilities management and compliance - legionella, gas, electrical - through group-level or regional contractors. No published source on how care groups procure BMS service was found, so this is inference: a small-site package, such as compliance monitoring with a monthly evidence report and a heat-alert dashboard, is likely to fit better than a full BMS project. It also travels well across a group of homes with similar plant.
Shaping the offer
A care home service built on this might include continuous water temperature logging with monthly evidence reports, TMV monitoring where the risk assessment calls for it, a summer heat dashboard tied to the alert levels, a boiler and calorifier sequencing check, and a winter readiness visit. Keep the legionella risk assessment and the water hygiene contractor in charge of the water safety regime - the controls support it, they do not replace it.
The BMS service visit covers the routine visit, and Seasonal changeover covers summer and winter switch-over checks.
Related tools and training: the care home temperature log analyser, the legionella setpoint checker, BMS service visit and seasonal changeover tools are in tecTools, and the LTHW system commissioning course is in tecTraining.
Sources mentioned: HSE guidance on legionella, hot and cold water systems and scalding in health and social care; CQC registration guidance on legionella risk assessment; NHS England on the Adverse Weather and Health Plan (2023); UKHSA and Met Office Heat-Health Alert action cards; UKHSA-commissioned research on extreme heat in adult social care. Outlet and cold water figures are from secondary summaries; the indoor heat threshold is not confirmed - agree it with the client.